MC100EL31DTR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 100EL |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Type | D-Type |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -4.2V~-5.7V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 100EL31 |
| JESD-30 Code | S-PDSO-G8 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.7V |
| Power Supplies | -4.5V |
| Supply Voltage-Min (Vsup) | 4.2V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 2.8GHz |
| Propagation Delay | 590 ps |
| Turn On Delay Time | 465 ps |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 32mA |
| Trigger Type | Positive Edge |
| Power Supply Current-Max (ICC) | 37mA |
| fmax-Min | 2200 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 2000000000Hz |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC100EL31DTR2 Overview
In the form of 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), it has been packaged. It is contained within the Tape & Reel (TR)package. T flip flop uses Differentialas the output. The trigger configured with it uses Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. A voltage of -4.2V~-5.7Vis required for its operation. A temperature of -40°C~85°C TAis used in the operation. Logic flip flops of this type are classified as D-Type. In FPGA terms, D flip flop is a type of 100ELseries FPGA. It should not exceed 2.8GHzin its output frequency. As a result, it consumes 32mA quiescent current. Terminations are 8. If you search by 100EL31, you will find similar parts. It is powered by a voltage of 5V . In this case, the electronic component is mounted in the way of Surface Mount. In this device, the clock edge trigger type is Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. Flip flops designed with 1bits are used in this part. In this case, the maximum supply voltage (Vsup) reaches 5.7V. Normal operation requires a supply voltage (Vsup) above 4.2V. 1 circuits are used to achieve its superior flexibility. Considering its reliability, this T flip flop is well suited for TAPE AND REEL. There are -4.5V power supplies attached to it. Additionally, you may refer to the additional NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V of the electronic flip flop.
MC100EL31DTR2 Features
Tape & Reel (TR) package
100EL series
1 Bits
-4.5V power supplies
MC100EL31DTR2 Applications
There are a lot of ON Semiconductor MC100EL31DTR2 Flip Flops applications.
- Storage Registers
- Balanced 24 mA output drivers
- Communications
- EMI reduction circuitry
- Single Up Count-Control Line
- Memory
- Dynamic threshold performance
- Shift Registers
- 2 – Bit synchronous counter
- Matched Rise and Fall
