MC100EL52DTR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 100EL |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -4.2V~-5.7V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 100EL52 |
| JESD-30 Code | S-PDSO-G8 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.7V |
| Power Supplies | -4.5V |
| Supply Voltage-Min (Vsup) | 4.2V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 2.8GHz |
| Propagation Delay | 465 ps |
| Turn On Delay Time | 365 ps |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 25mA |
| Trigger Type | Positive, Negative |
| Power Supply Current-Max (ICC) | 29mA |
| fmax-Min | 2200 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 2200000000Hz |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC100EL52DTR2 Overview
The item is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)cases. Package Tape & Reel (TR)embeds it. T flip flop uses Differentialas its output configuration. It is configured with a trigger that uses a value of Positive, Negative. It is mounted in the way of Surface Mount. A voltage of -4.2V~-5.7Vis used as the supply voltage. In the operating environment, the temperature is -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. In terms of FPGAs, it belongs to the 100EL series. Its output frequency should not exceed 2.8GHz Hz. This process consumes 25mA quiescents. There are 8 terminations,JK flip flop belongs to 100EL52 family. A voltage of 5V provides power to the D latch. There is an electronic component mounted in the way of Surface Mount. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This device is part of the FF/Latchesbase part number family. It is designed with 1bits. There is a 5.7Vmaximum supply voltage (Vsup). If you want to maintain normal operation, you should keep the supply voltage (Vsup) above 4.2V. Using 1 circuits, it is highly flexible. In light of its reliable performance, this T flip flop is well suited for TAPE AND REEL. A total of -4.5V power supplies are needed to run it. Additionally, there are NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V on the electronic flip flop that can be referred to.
MC100EL52DTR2 Features
Tape & Reel (TR) package
100EL series
1 Bits
-4.5V power supplies
MC100EL52DTR2 Applications
There are a lot of ON Semiconductor MC100EL52DTR2 Flip Flops applications.
- Frequency Divider circuits
- Reduced system switching noise
- EMI reduction circuitry
- Set-reset capability
- Common Clocks
- Latch-up performance
- Count Modes
- ESD performance
- Divide a clock signal by 2 or 4
- Automotive
