MC10EP29DTR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Series | 10EP |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -3V~-5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 10EP29 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 2 |
| Clock Frequency | 3GHz |
| Propagation Delay | 500 ps |
| Turn On Delay Time | 420 ps |
| Family | 10E |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 57mA |
| Number of Bits per Element | 1 |
| Trigger Type | Positive, Negative |
| High Level Output Current | -50mA |
| Low Level Output Current | 50mA |
| Power Supply Current-Max (ICC) | 60mA |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
MC10EP29DTR2 Overview
The flip flop is packaged in a case of 20-TSSOP (0.173, 4.40mm Width). Package Tape & Reel (TR)embeds it. There is a Differentialoutput configured with it. Positive, Negativeis the trigger it is configured with. Surface Mountis occupied by this electronic component. The supply voltage is set to -3V~-5.5V. -40°C~85°C TAis the operating temperature. It belongs to the type D-Typeof flip flops. In this case, it is a type of FPGA belonging to the 10EP series. It should not exceed 3GHzin terms of its output frequency. As a result, it consumes 57mA quiescent current. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. This D latch belongs to the family of 10EP29. It is powered by a voltage of 3.3V . The electronic device belongs to the 10Efamily. It is mounted in the way of Surface Mount. A total of 20pins are provided on this board. Its clock edge trigger type is Positive Edge. This device has the base part number FF/Latches. In this case, the maximum supply voltage (Vsup) reaches 5.5V. The supply voltage (Vsup) should be kept above 3V for normal operation. The superior flexibility of this product is achieved by using 2 circuits. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. There is also a characteristic of NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V. -50mAis set as the high level output current. In the low level output current setting, the current is set to 50mA.
MC10EP29DTR2 Features
Tape & Reel (TR) package
10EP series
20 pins
MC10EP29DTR2 Applications
There are a lot of ON Semiconductor MC10EP29DTR2 Flip Flops applications.
- Synchronous counter
- Storage registers
- Bus hold
- ATE
- Matched Rise and Fall
- Registers
- Differential Individual
- Convert a momentary switch to a toggle switch
- Data storage
- Data transfer
