MC10EP51DTR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 10EP |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -3V~-5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 10EP51 |
| Function | Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | -5.2V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 3GHz |
| Propagation Delay | 370 ps |
| Turn On Delay Time | 320 ps |
| Family | 10E |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 45mA |
| Prop. Delay@Nom-Sup | 0.42 ns |
| Trigger Type | Positive, Negative |
| High Level Output Current | -50mA |
| Low Level Output Current | 50mA |
| Power Supply Current-Max (ICC) | 47mA |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 3000000000Hz |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC10EP51DTR2 Overview
In the form of 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), it has been packaged. A package named Tape & Reel (TR)includes it. It is configured with Differentialas an output. This trigger is configured to use Positive, Negative. There is an electrical part that is mounted in the way of Surface Mount. A -3V~-5.5Vsupply voltage is required for it to operate. It is at -40°C~85°C TAdegrees Celsius that the system is operating. D-Typedescribes this flip flop. FPGAs belonging to the 10EPseries contain this type of chip. It should not exceed 3GHzin terms of its output frequency. This process consumes 45mA quiescents. 8terminations have occurred. The 10EP51family includes it. The D flip flop is powered by a voltage of 3.3V . It belongs to the family of electronic devices known as 10E. It is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 8. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. 1bits are used in its design. As soon as Vsup reaches 5.5V, the maximum supply voltage is reached. The supply voltage (Vsup) should be maintained above 3V for normal operation. Its flexibility is enhanced by 1 circuits. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. The D latch runs on a voltage of -5.2V volts. Additionally, you may refer to the additional NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V of the electronic flip flop. A high level output current of -50mAis set. In the low level output current setting, the current is set to 50mA.
MC10EP51DTR2 Features
Tape & Reel (TR) package
10EP series
8 pins
1 Bits
-5.2V power supplies
MC10EP51DTR2 Applications
There are a lot of ON Semiconductor MC10EP51DTR2 Flip Flops applications.
- Automotive
- Supports Live Insertion
- Buffer registers
- Patented noise
- Count Modes
- ESCC
- ATE
- Pattern generators
- Balanced 24 mA output drivers
- CMOS Process
