MC74AC74DTR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| Series | 74AC |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74AC74 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 160MHz |
| Propagation Delay | 14 ns |
| Turn On Delay Time | 6 ns |
| Family | AC |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 10ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 95000000Hz |
| Length | 5mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74AC74DTR2 Overview
The package is in the form of 14-TSSOP (0.173, 4.40mm Width). D flip flop is embedded in the Tape & Reel (TR) package. It is configured with Differentialas an output. It is configured with a trigger that uses Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. The JK flip flop operates at 2V~6Vvolts. It is at -40°C~85°C TAdegrees Celsius that the system is operating. It is an electronic flip flop with the type D-Type. It is a type of FPGA belonging to the 74AC series. A frequency of 160MHzshould not be exceeded by its output. As a result, it consumes 4μA of quiescent current without being affected by external factors. Currently, there are 14 terminations. D latch belongs to the 74AC74 family. A voltage of 5V provides power to the D latch. A JK flip flop with a 4.5pFfarad input capacitance is used here. An electronic device belonging to the family ACcan be found here. Electronic part Surface Mountis mounted in the way. This board has 14 pins. The clock edge trigger type for this device is Positive Edge. The part is included in FF/Latches. As soon as 6Vis reached, Vsup reaches its maximum value. Keeping the supply voltage (Vsup) above 2V is necessary for normal operation. The superior flexibility of this circuit is achieved by using 2 circuits. As a result of its reliable performance, this T flip flop is suitable for TAPE AND REEL. In order for the device to operate, it requires 5V power supplies. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. In order for the chip to function, it has 1output lines.
MC74AC74DTR2 Features
Tape & Reel (TR) package
74AC series
14 pins
5V power supplies
MC74AC74DTR2 Applications
There are a lot of ON Semiconductor MC74AC74DTR2 Flip Flops applications.
- Bounce elimination switch
- Shift Registers
- ESD performance
- Synchronous counter
- Frequency Divider circuits
- Latch-up performance
- ESD protection
- Load Control
- Cold spare funcion
- Consumer
