MC74ACT273DTR2G
| Parameters | |
|---|---|
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 200MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 6.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Halogen Free | Halogen Free |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74ACT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
MC74ACT273DTR2G Overview
The package is in the form of 20-TSSOP (0.173, 4.40mm Width). The package Tape & Reel (TR)contains it. It is configured with Non-Invertedas an output. It is configured with a trigger that uses a value of Positive Edge. Surface Mountis occupied by this electronic component. The JK flip flop operates at a voltage of 4.5V~5.5V. In the operating environment, the temperature is -40°C~85°C TA. A flip flop of this type is classified as a D-Type. The FPGA belongs to the 74ACT series. It should not exceed 200MHzin its output frequency. The list contains 1 elements. It consumes 8μA of quiescent current without being affected by external factors. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. Members of the 74ACT273family make up this object. The power supply voltage is 5V. The input capacitance of this JK flip flopis 4.5pF farads. An electronic device belonging to the family ACTcan be found here. A part of the electronic system is mounted in the way of Surface Mount. This board has 20 pins. It has a clock edge trigger type of Positive Edge. This part is included in FF/Latches. 8bits are used in its design. 8 circuits are used to achieve its superior flexibility. In view of its reliability, this D flip flop is a good fit for TAPE AND REEL. A total of 5V power supplies are needed to run it. In order to ensure high efficiency, the supply voltage should remain at 5V.
MC74ACT273DTR2G Features
Tape & Reel (TR) package
74ACT series
20 pins
8 Bits
5V power supplies
MC74ACT273DTR2G Applications
There are a lot of ON Semiconductor MC74ACT273DTR2G Flip Flops applications.
- 2 – Bit synchronous counter
- Control circuits
- Frequency Dividers
- Buffered Clock
- Computers
- Clock pulse
- Bounce elimination switch
- Bus hold
- Supports Live Insertion
- Guaranteed simultaneous switching noise level
