MC74ACT574DWR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 15 hours ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| Series | 74ACT |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74ACT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 100MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 2.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Halogen Free | Halogen Free |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MC74ACT574DWR2G Overview
In the form of 20-SOIC (0.295, 7.50mm Width), it has been packaged. You can find it in the Tape & Reel (TR)package. T flip flop is configured with an output of Tri-State, Non-Inverted. This trigger is configured to use Positive Edge. It is mounted in the way of Surface Mount. It operates with a supply voltage of 4.5V~5.5V. It is operating at -40°C~85°C TA. D-Typedescribes this flip flop. In terms of FPGAs, it belongs to the 74ACT series. A frequency of 100MHzshould not be exceeded by its output. A total of 1elements are contained within it. There is 8μA quiescent consumption. It has been determined that there have been 20 terminations. The 74ACT574 family contains this object. Power is supplied from a voltage of 5V volts. The input capacitance of this JK flip flopis 4.5pF farads. It is a member of the ACTfamily of D flip flop. It is mounted in the way of Surface Mount. 20pins are included in its design. This device has the clock edge trigger type of Positive Edge. The part is included in FF/Latches. This flip flop is designed with 8 Bits. The superior flexibility of this circuit is achieved by using 8 circuits. This D flip flop is well suited for TR based on its reliable performance. The D latch runs on a voltage of 5V volts. The D flip flop is embedded with 2ports. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. It operates with 3 output lines.
MC74ACT574DWR2G Features
Tape & Reel (TR) package
74ACT series
20 pins
8 Bits
5V power supplies
MC74ACT574DWR2G Applications
There are a lot of ON Semiconductor MC74ACT574DWR2G Flip Flops applications.
- EMI reduction circuitry
- Functionally equivalent to the MC10/100EL29
- Instrumentation
- Consumer
- Shift registers
- Data storage
- Communications
- Bus hold
- Memory
- Shift Registers
