MC74ACT74NG
| Parameters | |
|---|---|
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Base Part Number | 74ACT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Clock Frequency | 210MHz |
| Propagation Delay | 13 ns |
| Turn On Delay Time | 5.5 ns |
| Family | ACT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 6.35mm |
| Length | 6.35mm |
| Width | 25.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Weight | 4.535924g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| Series | 74ACT |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
MC74ACT74NG Overview
The flip flop is packaged in a case of 14-DIP (0.300, 7.62mm). D flip flop is embedded in the Tube package. Differentialis the output configured for it. It is configured with a trigger that uses Positive Edge. This electronic part is mounted in the way of Through Hole. A supply voltage of 4.5V~5.5V is required for operation. -40°C~85°C TAis the operating temperature. Logic flip flops of this type are classified as D-Type. This type of FPGA is a part of the 74ACT series. A frequency of 210MHzshould not be exceeded by its output. It consumes 4μA of quiescent In 14terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. This D latch belongs to the family of 74ACT74. A voltage of 5V is used to power it. Input capacitance of this device is 4.5pF farads. It is a member of the ACTfamily of D flip flop. In this case, the electronic component is mounted in the way of Through Hole. There are 14pins on it. This device exhibits a clock edge trigger type of Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. Due to its superior flexibility, it uses 2 circuits. The D latch operates on 5V volts. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. With an output current of 24mA, it is possible to design the device in any way you want. To operate, the chip has a total of 1 output lines.
MC74ACT74NG Features
Tube package
74ACT series
14 pins
5V power supplies
MC74ACT74NG Applications
There are a lot of ON Semiconductor MC74ACT74NG Flip Flops applications.
- Counters
- Differential Individual
- Communications
- Divide a clock signal by 2 or 4
- High Performance Logic for test systems
- 2 – Bit synchronous counter
- Shift registers
- Bounce elimination switch
- Bus hold
- Asynchronous counter
