MC74HCT273ADWR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | 74HCT |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HCT273 |
| Function | Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Channels | 8 |
| Output Current | 4mA |
| Number of Bits | 8 |
| Clock Frequency | 30MHz |
| Propagation Delay | 25 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 25 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Halogen Free | Halogen Free |
| Current - Output High, Low | 4mA 4mA |
| Max Propagation Delay @ V, Max CL | 25ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MC74HCT273ADWR2G Overview
The package is in the form of 20-SOIC (0.295, 7.50mm Width). D flip flop is embedded in the Tape & Reel (TR) package. As configured, the output uses Non-Inverted. The trigger it is configured with uses Positive Edge. This electronic part is mounted in the way of Surface Mount. A supply voltage of 4.5V~5.5V is required for operation. Temperature is set to -55°C~125°C TA. Logic flip flops of this type are classified as D-Type. In this case, it is a type of FPGA belonging to the 74HCT series. You should not exceed 30MHzin the output frequency of the device. D latch consists of 1 elements. Currently, there are 20 terminations. The 74HCT273 family contains this object. The power source is powered by 5V. A device of this type belongs to the family of HCT. A part of the electronic system is mounted in the way of Surface Mount. With its 20pins, it is designed to work with most electronic flip flops. This device's clock edge trigger type is Positive Edge. This device is part of the FF/Latchesbase part number family. An electronic part with 8bits has been designed. As a result of its reliability, this D flip flop is ideally suited for TAPE AND REEL. A total of 5V power supplies are needed to run it. Optimal efficiency requires a supply voltage of 5V. With an output current of 4mA, it is possible to design the device in any way you want. Despite external influences, it consumes 4μAof quiescent current. Currently, there are 8 channels available.
MC74HCT273ADWR2G Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
5V power supplies
MC74HCT273ADWR2G Applications
There are a lot of ON Semiconductor MC74HCT273ADWR2G Flip Flops applications.
- Automotive
- Data storage
- Bounce elimination switch
- Balanced 24 mA output drivers
- Instrumentation
- Shift Registers
- Data Synchronizers
- Bus hold
- Functionally equivalent to the MC10/100EL29
- Balanced Propagation Delays
