MC74HCT574ADWR2G
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | 74HCT |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 250 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HCT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 30MHz |
| Propagation Delay | 45 ns |
| Turn On Delay Time | 30 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop, Latch |
| Current - Quiescent (Iq) | 4μA |
| Halogen Free | Halogen Free |
| Current - Output High, Low | 6mA 6mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 30ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.4mm |
| Length | 12.95mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
MC74HCT574ADWR2G Overview
It is packaged in the way of 20-SOIC (0.295, 7.50mm Width). Package Tape & Reel (TR)embeds it. The output it is configured with uses Tri-State, Non-Inverted. It is configured with the trigger Positive Edge. Surface Mountis occupied by this electronic component. A 4.5V~5.5Vsupply voltage is required for it to operate. A temperature of -55°C~125°C TAis used in the operation. D-Typedescribes this flip flop. The FPGA belongs to the 74HCT series. In order for it to function properly, its output frequency should not exceed 30MHz. In total, there are 1 elements. As a result, it consumes 4μA of quiescent current without being affected by external factors. The number of terminations is 20. This D latch belongs to the family of 74HCT574. A voltage of 5V is used to power it. The input capacitance of this T flip flop is 10pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. In terms of electronic devices, this device belongs to the HCTfamily of devices. There is an electronic component mounted in the way of Surface Mount. 20pins are included in its design. The clock edge trigger type for this device is Positive Edge. This RS flip flops is a part number FF/Latches. An electronic part with 8bits has been designed. In order to achieve its superior flexibility, 8 circuits are used. As a result of its reliability, this D flip flop is ideally suited for TR. In order for the device to operate, it requires 5V power supplies. The D flip flop is embedded with 2ports. In order to ensure high efficiency, the supply voltage should remain at 5V. There are 3 output lines in this JK flip flop.
MC74HCT574ADWR2G Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
5V power supplies
MC74HCT574ADWR2G Applications
There are a lot of ON Semiconductor MC74HCT574ADWR2G Flip Flops applications.
- Storage Registers
- ESCC
- ESD performance
- Differential Individual
- Bounce elimination switch
- Data storage
- Computers
- Guaranteed simultaneous switching noise level
- QML qualified product
- Parallel data storage
