MC74VHC574DW
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| Series | 74VHC |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 3.3V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74VHC574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 2/5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 115MHz |
| Propagation Delay | 16.7 ns |
| Turn On Delay Time | 5.6 ns |
| Family | AHC/VHC |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74VHC574DW Overview
The item is packaged in 20-SOIC (0.295, 7.50mm Width)cases. It is contained within the Tubepackage. Tri-State, Non-Invertedis the output configured for it. This trigger uses the value Positive Edge. Surface Mountis positioned in the way of this electronic part. The JK flip flop operates with an input voltage of 2V~5.5V volts. A temperature of -40°C~85°C TAis considered to be the operating temperature. This D latch has the type D-Type. In terms of FPGAs, it belongs to the 74VHC series. A frequency of 115MHzshould not be exceeded by its output. In total, it contains 1 elements. During its operation, it consumes 4μA quiescent energy. 20terminations have occurred. The 74VHC574family includes it. It is powered by a voltage of 3.3V . Its input capacitance is 4pFfarads. AHC/VHCis the family of this D flip flop. The electronic part is mounted in the way of Surface Mount. This board has 20 pins. It has a clock edge trigger type of Positive Edge. The part you are looking for is included in FF/Latches. The design is based on 8bits. It reaches the maximum supply voltage (Vsup) at 5.5V. If you want to maintain normal operation, you should keep the supply voltage (Vsup) above 2V. The superior flexibility is achieved through the use of 8 circuits. As a result of its reliability, this D flip flop is ideally suited for RAIL. The system runs on a power supply of 2/5.5V watts. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. There are 3 output lines in this JK flip flop.
MC74VHC574DW Features
Tube package
74VHC series
20 pins
8 Bits
2/5.5V power supplies
MC74VHC574DW Applications
There are a lot of ON Semiconductor MC74VHC574DW Flip Flops applications.
- Circuit Design
- Reduced system switching noise
- Balanced 24 mA output drivers
- Consumer
- Memory
- Load Control
- Test & Measurement
- Computing
- Cold spare funcion
- CMOS Process
