NLAS4501DFT2
| Parameters | |
|---|---|
| Lifecycle Status | OBSOLETE (Last Updated: 1 day ago) |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 25Ohm |
| Terminal Finish | Tin/Lead (Sn80Pb20) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 150mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | NLAS4501 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Power Dissipation | 150mW |
| Throw Configuration | SPST |
| Turn On Delay Time | 14 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 22 ns |
| -3db Bandwidth | 220MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 93 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 10pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 9ns, 10ns |
| Charge Injection | 3pC |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Length | 2mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
NLAS4501DFT2 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 5-TSSOP, SC-70-5, SOT-353. High reliability is achieved by using advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. The operating temperature is extended to around -55°C~125°C TA. Totally, there are 5 terminations. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 3V volts, the electrical component should be turned on and run. 5 pins are injected to the electronic part body. These analog multiplexers are built based on SPST - NO switching circuits. Try searching with NLAS4501 to find analog multiplexer variants. As far as internal resistance is concerned, it has 25Ohm. The datasheets for the 5 pins explain the functions. Multiplexer or Switches is a typical switch device. A voltage higher than 5.5V should not normally be supplied to the switches. Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 2V. This multiplexer would work with 1μA current. A voltage of 2V~5.5V is required for this switch device, which drains from a single voltage source. Operating voltages of 5V are compatible with the electrical part.
NLAS4501DFT2 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 220MHz
NLAS4501DFT2 Applications
There are a lot of ON Semiconductor NLAS4501DFT2 Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- Precision data acquisition
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Battery-powered systems
- SONET
- DSLAMs
- Channel Banks
- Cross Connects
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Wireless Local Loop
