SN74ABT162823ADGGR
| Parameters | |
|---|---|
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Power Supply Current-Max (ICC) | 80mA |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 150000000Hz |
| Length | 14mm |
| Width | 6.1mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 56-TFSOP (0.240, 6.10mm Width) |
| Number of Pins | 56 |
| Weight | 252.792698mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ABT |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 56 |
| Type | D-Type |
| Additional Feature | WITH CLEAR AND CLOCK ENABLE |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ABT162823 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Number of Ports | 2 |
| Output Current | 12mA |
| Number of Bits | 18 |
| Clock Frequency | 150MHz |
| Propagation Delay | 6.2 ns |
| Turn On Delay Time | 2.3 ns |
| Family | ABT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 500μA |
| Current - Output High, Low | 12mA 12mA |
| Number of Bits per Element | 9 |
| Max Propagation Delay @ V, Max CL | 6.2ns @ 5V, 50pF |
| Prop. Delay@Nom-Sup | 7.5 ns |
SN74ABT162823ADGGR Overview
The flip flop is packaged in 56-TFSOP (0.240, 6.10mm Width). There is an embedded version in the package Cut Tape (CT). T flip flop is configured with an output of Tri-State, Non-Inverted. In the configuration of the trigger, Positive Edgeis used. It is mounted in the way of Surface Mount. The supply voltage is set to 4.5V~5.5V. Temperature is set to -40°C~85°C TA. A flip flop of this type is classified as a D-Type. This type of FPGA is a part of the 74ABT series. This D flip flop should not have a frequency greater than 150MHz. In total, there are 2 elements. There is a consumption of 500μAof quiescent energy. There are 56 terminations,You can search similar parts based on 74ABT162823. It is powered by a voltage of 5V . This JK flip flop has a 3.5pFfarad input capacitance. Devices in the ABTfamily are electronic devices. There is an electronic part that is mounted in the way of Surface Mount. There are 56pins on it. This device has Positive Edgeas its clock edge trigger type. There is a FF/Latchesbase part number assigned to the RS flip flops. The design is based on 18bits. As soon as Vsup reaches 5.5V, the maximum supply voltage is reached. Normally, the supply voltage (Vsup) should be kept above 4.5V. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. The D latch runs on a voltage of 5V volts. The flip flop has 2embedded ports. As a result of its output current of 12mA, it is very flexible in terms of design. The JK flip flop is with 3 output lines to operate. It is also characterized by WITH CLEAR AND CLOCK ENABLE.
SN74ABT162823ADGGR Features
Cut Tape (CT) package
74ABT series
56 pins
18 Bits
5V power supplies
SN74ABT162823ADGGR Applications
There are a lot of Texas Instruments SN74ABT162823ADGGR Flip Flops applications.
- Count Modes
- Storage registers
- Guaranteed simultaneous switching noise level
- Pattern generators
- Safety Clamp
- Asynchronous counter
- Consumer
- Buffer registers
- Memory
- 2 – Bit synchronous counter
