SN74ABT273NSR
| Parameters | |
|---|---|
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 6.8ns @ 5V, 50pF |
| Prop. Delay@Nom-Sup | 7.3 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 7pF |
| Power Supply Current-Max (ICC) | 30mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2mm |
| Length | 12.6mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 266.712314mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ABT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ABT273 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 64mA |
| Number of Bits | 8 |
| Clock Frequency | 150MHz |
| Propagation Delay | 6.8 ns |
| Turn On Delay Time | 2.5 ns |
| Family | ABT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 400μA |
| Current - Output High, Low | 32mA 64mA |
SN74ABT273NSR Overview
The package is in the form of 20-SOIC (0.209, 5.30mm Width). As part of the package Tape & Reel (TR), it is embedded. It is configured with Non-Invertedas an output. This trigger uses the value Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. A supply voltage of 4.5V~5.5V is required for operation. In the operating environment, the temperature is -40°C~85°C TA. This logic flip flop is classified as type D-Type. This type of FPGA is a part of the 74ABT series. A frequency of 150MHzshould not be exceeded by its output. A total of 1 elements are present. This process consumes 400μA quiescents. A total of 20 terminations have been made. It is a member of the 74ABT273 family. A voltage of 5V provides power to the D latch. A 7pFfarad input capacitance is provided by this T flip flop. Electronic devices of this type belong to the ABTfamily. Electronic part Surface Mountis mounted in the way. This board has 20 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The RS flip flops belongs to FF/Latches base part number. 8bits are used in its design. The superior flexibility of this product is achieved by using 8 circuits. As a result of its reliability, this D flip flop is ideally suited for TR. The D latch runs on a voltage of 5V volts. For high efficiency, the supply voltage should be set to 5V. The output current of 64mA makes it feature maximum design flexibility.
SN74ABT273NSR Features
Tape & Reel (TR) package
74ABT series
20 pins
8 Bits
5V power supplies
SN74ABT273NSR Applications
There are a lot of Texas Instruments SN74ABT273NSR Flip Flops applications.
- Instrumentation
- Synchronous counter
- ESCC
- QML qualified product
- Storage Registers
- Data storage
- Cold spare funcion
- Data transfer
- Pattern generators
- Convert a momentary switch to a toggle switch
