SN74ABT377APWR
| Parameters | |
|---|---|
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | WITH HOLD MODE |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74ABT377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 64mA |
| Number of Bits | 8 |
| Clock Frequency | 150MHz |
| Propagation Delay | 7.3 ns |
| Turn On Delay Time | 4.5 ns |
| Family | ABT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 250μA |
| Current - Output High, Low | 32mA 64mA |
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 6.8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Power Supply Current-Max (ICC) | 30mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ABT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
SN74ABT377APWR Overview
It is packaged in the way of 20-TSSOP (0.173, 4.40mm Width). It is contained within the Cut Tape (CT)package. The output it is configured with uses Non-Inverted. This trigger uses the value Positive Edge. It is mounted in the way of Surface Mount. It operates with a supply voltage of 4.5V~5.5V. Currently, the operating temperature is -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. This type of FPGA is a part of the 74ABT series. There should be no greater frequency than 150MHzon its output. A total of 1 elements are present. There is 250μA quiescent consumption. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. This D latch belongs to the family of 74ABT377. The power source is powered by 5V. A 3.5pFfarad input capacitance is provided by this T flip flop. The electronic device belongs to the ABTfamily. There is an electronic component mounted in the way of Surface Mount. With its 20pins, it is designed to work with most electronic flip flops. The clock edge trigger type for this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. 8bits are used in its design. The superior flexibility is achieved through the use of 8 circuits. Compared to other similar T flip flops, this device offers reliable performance and is well suited for TR. The D latch operates on 5V volts. The supply voltage should be maintained at 5V for high efficiency. This T flip flop features a maximum design flexibility due to its output current of 64mA. Additionally, there are WITH HOLD MODE on the electronic flip flop that can be referred to.
SN74ABT377APWR Features
Cut Tape (CT) package
74ABT series
20 pins
8 Bits
5V power supplies
SN74ABT377APWR Applications
There are a lot of Texas Instruments SN74ABT377APWR Flip Flops applications.
- High Performance Logic for test systems
- Divide a clock signal by 2 or 4
- Buffer registers
- Data Synchronizers
- Convert a momentary switch to a toggle switch
- ESD performance
- Common Clocks
- Safety Clamp
- Reduced system switching noise
- Balanced 24 mA output drivers
