SN74ABT574APWR
| Parameters | |
|---|---|
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74ABT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 64mA |
| Number of Bits | 8 |
| Clock Frequency | 200MHz |
| Propagation Delay | 6.6 ns |
| Quiescent Current | 30mA |
| Turn On Delay Time | 3.9 ns |
| Family | ABT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 250μA |
| Current - Output High, Low | 32mA 64mA |
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 6.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ABT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
SN74ABT574APWR Overview
It is packaged in the way of 20-TSSOP (0.173, 4.40mm Width). As part of the package Cut Tape (CT), it is embedded. Currently, the output is configured to use Tri-State, Non-Inverted. The trigger it is configured with uses Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. A 4.5V~5.5Vsupply voltage is required for it to operate. -40°C~85°C TAis the operating temperature. D-Typeis the type of this D latch. This type of FPGA is a part of the 74ABT series. Its output frequency should not exceed 200MHz Hz. A total of 1 elements are present. This process consumes 250μA quiescents. A total of 20terminations have been recorded. If you search by 74ABT574, you will find similar parts. The power source is powered by 5V. There is 3.5pF input capacitance for this T flip flop. An electronic device belonging to the family ABTcan be found here. It is mounted by the way of Surface Mount. This board is designed with 20pins on it. The clock edge trigger type for this device is Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. This flip flop is designed with 8 Bits. To achieve this superior flexibility, 8 circuits are used. On the basis of its reliable performance, this D flip flop is well suited for use with TR. The D latch runs on a voltage of 5V volts. The flip flop has 2embedded ports. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. The 64mA output current allows it to be designed with the greatest amount of flexibility. The JK flip flop is with 3 output lines to operate. Despite external influences, it consumes 30mAof quiescent current.
SN74ABT574APWR Features
Cut Tape (CT) package
74ABT series
20 pins
8 Bits
5V power supplies
SN74ABT574APWR Applications
There are a lot of Texas Instruments SN74ABT574APWR Flip Flops applications.
- Latch
- ESD performance
- ATE
- Divide a clock signal by 2 or 4
- Balanced 24 mA output drivers
- Power down protection
- Circuit Design
- ESCC
- Balanced Propagation Delays
- QML qualified product
