SN74AC374PW
| Parameters | |
|---|---|
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AC374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 155MHz |
| Propagation Delay | 13.5 ns |
| Turn On Delay Time | 8 ns |
| Family | AC |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 9.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 60000000Hz |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
SN74AC374PW Overview
The item is packaged in 20-TSSOP (0.173, 4.40mm Width)cases. The Tubepackage contains it. T flip flop uses Tri-State, Non-Invertedas the output. Positive Edgeis the trigger it is configured with. Surface Mountis positioned in the way of this electronic part. A voltage of 2V~6Vis required for its operation. -40°C~85°C TAis the operating temperature. Logic flip flops of this type are classified as D-Type. In this case, it is a type of FPGA belonging to the 74AC series. Its output frequency should not exceed 155MHz Hz. D latch consists of 1 elements. There is 4μA quiescent consumption. The number of terminations is 20. The 74AC374 family contains it. The power source is powered by 3.3V. Input capacitance of this device is 4.5pF farads. ACis the family of this D flip flop. This electronic part is mounted in the way of Surface Mount. The 20pins are designed into the board. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This part is included in FF/Latches. An electronic part designed with 8bits is used in this application. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. Normal operation requires a supply voltage (Vsup) above 2V. The superior flexibility of this product is achieved by using 8 circuits. A total of 2ports are embedded in the D flip flop. The 24mA output current allows it to be designed with the greatest amount of flexibility. Currently, there are 3 input lines present.
SN74AC374PW Features
Tube package
74AC series
20 pins
8 Bits
SN74AC374PW Applications
There are a lot of Texas Instruments SN74AC374PW Flip Flops applications.
- Dynamic threshold performance
- High Performance Logic for test systems
- Pattern generators
- Shift registers
- Modulo – n – counter
- Balanced Propagation Delays
- Common Clocks
- 2 – Bit synchronous counter
- Data Synchronizers
- Single Up Count-Control Line
