SN74AC564PW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Termination | SMD/SMT |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AC564 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Inverted |
| Max Output Current | 24mA |
| Number of Elements | 1 |
| Polarity | Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 95MHz |
| Propagation Delay | 14 ns |
| Turn On Delay Time | 4.9 ns |
| Family | AC |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AC564PW Overview
In the form of 20-TSSOP (0.173, 4.40mm Width), it has been packaged. D flip flop is included in the Tubepackage. Tri-State, Invertedis the output configured for it. This trigger uses the value Positive Edge. There is an electric part mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 2V~6V volts. It is operating at a temperature of -40°C~85°C TA. This D latch has the type D-Type. JK flip flop belongs to the 74ACseries of FPGAs. There should be no greater frequency than 95MHzon its output. The list contains 1 elements. It consumes 4μA of quiescent There are 20 terminations,It is a member of the 74AC564 family. It is powered by a voltage of 3.3V . The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. A device of this type belongs to the family of AC. This electronic part is mounted in the way of Surface Mount. Basically, it is designed with a set of 20 pins. There is a clock edge trigger type of Positive Edgeon this device. There is a base part number FF/Latchesfor the RS flip flops. Flip flops designed with 8bits are used in this part. There is a 6Vmaximum supply voltage (Vsup). For normal operation, the supply voltage (Vsup) should be above 2V. The superior flexibility is achieved through the use of 8 circuits. The flip flop contains 2ports. Featuring the maximum design flexibility, it has an output current of 24mA . As of now, there are 3input lines.
SN74AC564PW Features
Tube package
74AC series
20 pins
8 Bits
SN74AC564PW Applications
There are a lot of Texas Instruments SN74AC564PW Flip Flops applications.
- Instrumentation
- Single Up Count-Control Line
- Test & Measurement
- Storage registers
- Cold spare funcion
- Data Synchronizers
- Common Clocks
- Parallel data storage
- Registers
- High Performance Logic for test systems
