SN74ACT534N
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Weight | 1.1991g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT534 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 100MHz |
| Propagation Delay | 11.5 ns |
| Turn On Delay Time | 2.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 5.08mm |
| Length | 24.33mm |
| Width | 6.35mm |
| Thickness | 4.57mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ACT534N Overview
In the form of 20-DIP (0.300, 7.62mm), it has been packaged. The package Tubecontains it. T flip flop is configured with an output of Tri-State, Inverted. Positive Edgeis the trigger it is configured with. It is mounted in the way of Through Hole. A voltage of 4.5V~5.5Vis used as the supply voltage. It is operating at -40°C~85°C TA. A flip flop of this type is classified as a D-Type. This type of FPGA is a part of the 74ACT series. You should not exceed 100MHzin the output frequency of the device. In total, it contains 1 elements. As a result, it consumes 4μA quiescent current and is not affected by external forces. There have been 20 terminations. Members of the 74ACT534family make up this object. An input voltage of 5Vpowers the D latch. The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. ACTis the family of this D flip flop. In this case, the electronic component is mounted in the way of Through Hole. With its 20pins, it is designed to work with most electronic flip flops. A Positive Edgeclock edge trigger is used in this device. There is a FF/Latchesbase part number assigned to the RS flip flops. It is designed with a number of bits of 8. Its superior flexibility is attributed to its use of 8 circuits. The system runs on a power supply of 5V watts. The D flip flop has no ports embedded. Optimal efficiency requires a supply voltage of 5V. The output current of 24mA makes it feature maximum design flexibility. There are 3 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply.
SN74ACT534N Features
Tube package
74ACT series
20 pins
8 Bits
5V power supplies
SN74ACT534N Applications
There are a lot of Texas Instruments SN74ACT534N Flip Flops applications.
- Shift Registers
- Bus hold
- Storage Registers
- Registers
- Reduced system switching noise
- Functionally equivalent to the MC10/100EL29
- Control circuits
- Computers
- Single Down Count-Control Line
- ESD performance
