SN74ACT574DWR
| Parameters | |
|---|---|
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ACT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 50mA |
| Number of Bits | 8 |
| Clock Frequency | 110MHz |
| Propagation Delay | 12 ns |
| Turn On Delay Time | 7 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 2.65mm |
| Length | 12.8mm |
SN74ACT574DWR Overview
It is embeded in 20-SOIC (0.295, 7.50mm Width) case. There is an embedded version in the package Tape & Reel (TR). T flip flop is configured with an output of Tri-State, Non-Inverted. JK flip flop uses Positive Edgeas the trigger. The electronic part is mounted in the way of Surface Mount. A 4.5V~5.5Vsupply voltage is required for it to operate. In this case, the operating temperature is -40°C~85°C TA. The type of this D latch is D-Type. The FPGA belongs to the 74ACT series. This D flip flop should not have a frequency greater than 110MHz. A total of 1elements are present in it. It consumes 4μA of quiescent 20terminations have occurred. It is a member of the 74ACT574 family. An input voltage of 5Vpowers the D latch. Its input capacitance is 4.5pF farads. A device of this type belongs to the family of ACT. The electronic part is mounted in the way of Surface Mount. 20pins are included in its design. This device exhibits a clock edge trigger type of Positive Edge. The part is included in FF/Latches. Flip flops designed with 8bits are used in this part. To achieve this superior flexibility, 8 circuits are used. As a result of its reliability, this D flip flop is ideally suited for TR. The D latch operates on 5V volts. The D flip flop has no ports embedded. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 50mA. It is reported that there are 3 input lines.
SN74ACT574DWR Features
Tape & Reel (TR) package
74ACT series
20 pins
8 Bits
5V power supplies
SN74ACT574DWR Applications
There are a lot of Texas Instruments SN74ACT574DWR Flip Flops applications.
- Buffered Clock
- Single Up Count-Control Line
- ATE
- Frequency Dividers
- Balanced 24 mA output drivers
- Data storage
- Power down protection
- Common Clocks
- Data transfer
- ESCC
