SN74ACT574N
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Weight | 1.1991g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Bus Driver/Transceiver |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | 74ACT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 110MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 7 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 5.08mm |
| Length | 24.33mm |
| Width | 6.35mm |
| Thickness | 4.57mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ACT574N Overview
In the form of 20-DIP (0.300, 7.62mm), it has been packaged. There is an embedded version in the package Tube. In the configuration, Tri-State, Non-Invertedis used as the output. JK flip flop uses Positive Edgeas the trigger. This electronic part is mounted in the way of Through Hole. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. It is operating at -40°C~85°C TA. D-Typedescribes this flip flop. It is a type of FPGA belonging to the 74ACT series. In order for it to function properly, its output frequency should not exceed 110MHz. D latch consists of 1 elements. There is a consumption of 4μAof quiescent energy. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. D latch belongs to the 74ACT574 family. A voltage of 5V is used as the power supply for this D latch. The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. In this case, the D flip flop belongs to the ACTfamily. The electronic part is mounted in the way of Through Hole. With its 20pins, it is designed to work with most electronic flip flops. It has a clock edge trigger type of Positive Edge. There is a base part number Bus Driver/Transceiverfor the RS flip flops. The flip flop is designed with 8bits. 8 circuits are used to achieve its superior flexibility. The D latch runs on a voltage of 5V volts. The flip flop has 2embedded ports. The supply voltage should be maintained at 5V for high efficiency. With an output current of 24mA, this device offers maximum design flexibility. 3input lines are available for you to choose from.
SN74ACT574N Features
Tube package
74ACT series
20 pins
8 Bits
5V power supplies
SN74ACT574N Applications
There are a lot of Texas Instruments SN74ACT574N Flip Flops applications.
- CMOS Process
- Convert a momentary switch to a toggle switch
- Balanced 24 mA output drivers
- Bounce elimination switch
- Guaranteed simultaneous switching noise level
- Storage registers
- Dynamic threshold performance
- Cold spare funcion
- Storage Registers
- ESCC
