SN74ACT574PW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74ACT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 110MHz |
| Propagation Delay | 12 ns |
| Turn On Delay Time | 7 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ACT574PW Overview
In the form of 20-TSSOP (0.173, 4.40mm Width), it has been packaged. A package named Tubeincludes it. T flip flop uses Tri-State, Non-Invertedas its output configuration. It is configured with a trigger that uses a value of Positive Edge. Surface Mountis positioned in the way of this electronic part. A 4.5V~5.5Vsupply voltage is required for it to operate. It is at -40°C~85°C TAdegrees Celsius that the system is operating. It belongs to the type D-Typeof flip flops. It belongs to the 74ACTseries of FPGAs. This D flip flop should not have a frequency greater than 110MHz. The list contains 1 elements. T flip flop consumes 4μA quiescent energy. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. If you search by 74ACT574, you will find similar parts. A voltage of 5V is used as the power supply for this D latch. JK flip flop input capacitance is 4.5pF farads. In this case, the D flip flop belongs to the ACTfamily. The electronic part is mounted in the way of Surface Mount. There are 20pins on it. A Positive Edgeclock edge trigger is used in this device. It is included in FF/Latches. Flip flops designed with 8bits are used in this part. The superior flexibility is achieved through the use of 8 circuits. There are 5V power supplies attached to it. This flip flop has a total of 2ports. In order to achieve high efficiency, the supply voltage should be maintained at 5V. The output current of 24mA makes it feature maximum design flexibility. 3input lines are available for you to choose from.
SN74ACT574PW Features
Tube package
74ACT series
20 pins
8 Bits
5V power supplies
SN74ACT574PW Applications
There are a lot of Texas Instruments SN74ACT574PW Flip Flops applications.
- Guaranteed simultaneous switching noise level
- Shift Registers
- Storage Registers
- Buffer registers
- Data storage
- Balanced 24 mA output drivers
- Cold spare funcion
- Differential Individual
- Single Down Count-Control Line
- Dynamic threshold performance
