SN74AHC16374DGVR
| Parameters | |
|---|---|
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 8mA |
| Number of Bits | 16 |
| Clock Frequency | 120MHz |
| Propagation Delay | 16.2 ns |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 10.1ns @ 5V, 50pF |
| Prop. Delay@Nom-Sup | 11.5 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 2.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 1.2mm |
| Length | 9.7mm |
| Width | 4.4mm |
| Thickness | 1.05mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-TFSOP (0.173, 4.40mm Width) |
| Number of Pins | 48 |
| Weight | 123.490523mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74AHC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.4mm |
| Base Part Number | 74AHC16374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 2 |
SN74AHC16374DGVR Overview
48-TFSOP (0.173, 4.40mm Width)is the packaging method. The package Cut Tape (CT)contains it. T flip flop is configured with an output of Tri-State, Non-Inverted. The trigger configured with it uses Positive Edge. There is an electric part mounted in the way of Surface Mount. A 2V~5.5Vsupply voltage is required for it to operate. It is operating at a temperature of -40°C~85°C TA. D-Typedescribes this flip flop. JK flip flop is a part of the 74AHCseries of FPGAs. It should not exceed 120MHzin terms of its output frequency. The element count is 2 . As a result, it consumes 4μA quiescent current. Currently, there are 48 terminations. If you search by 74AHC16374, you will find similar parts. A voltage of 3.3V is used to power it. JK flip flop input capacitance is 2.5pF farads. The electronic device belongs to the AHC/VHC/H/U/Vfamily. It is mounted by the way of Surface Mount. Basically, it is designed with a set of 48 pins. In this device, the clock edge trigger type is Positive Edge. The RS flip flops belongs to FF/Latches base part number. The flip flop is designed with 16bits. Vsup reaches its maximum value at 5.5V. For normal operation, the supply voltage (Vsup) should be above 2V. Considering the reliability of this T flip flop, it is well suited for TR. A D flip flop with 2embedded ports is available. Its output current of 8mAallows for maximum design flexibility. In order for the chip to function, it has 3output lines.
SN74AHC16374DGVR Features
Cut Tape (CT) package
74AHC series
48 pins
16 Bits
SN74AHC16374DGVR Applications
There are a lot of Texas Instruments SN74AHC16374DGVR Flip Flops applications.
- Frequency Divider circuits
- Modulo – n – counter
- Frequency division
- Bus hold
- Asynchronous counter
- Single Up Count-Control Line
- Storage registers
- Circuit Design
- Guaranteed simultaneous switching noise level
- Count Modes
