SN74AHC16374DLR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-BSSOP (0.295, 7.50mm Width) |
| Number of Pins | 48 |
| Weight | 600.301152mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AHC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 48 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Base Part Number | 74AHC16374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 8mA |
| Number of Bits | 16 |
| Clock Frequency | 120MHz |
| Propagation Delay | 18.5 ns |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 10.1ns @ 5V, 50pF |
| Prop. Delay@Nom-Sup | 11.5 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 2.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 2.79mm |
| Length | 15.88mm |
| Width | 7.49mm |
| Thickness | 2.59mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHC16374DLR Overview
The flip flop is packaged in a case of 48-BSSOP (0.295, 7.50mm Width). You can find it in the Tape & Reel (TR)package. Tri-State, Non-Invertedis the output configured for it. JK flip flop uses Positive Edgeas the trigger. The electronic part is mounted in the way of Surface Mount. It operates with a supply voltage of 2V~5.5V. Temperature is set to -40°C~85°C TA. This logic flip flop is classified as type D-Type. In FPGA terms, D flip flop is a type of 74AHCseries FPGA. This D flip flop should not have a frequency greater than 120MHz. D latch consists of 2 elements. During its operation, it consumes 4μA quiescent energy. A total of 48terminations have been recorded. This D latch belongs to the family of 74AHC16374. The power supply voltage is 3.3V. This T flip flop has a capacitance of 2.5pF farads at the input. Devices in the AHC/VHC/H/U/Vfamily are electronic devices. In this case, the electronic component is mounted in the way of Surface Mount. A total of 48pins are provided on this board. This device's clock edge trigger type is Positive Edge. It is part of the FF/Latchesbase part number family. 16bits are used in its design. As soon as 5.5Vis reached, Vsup reaches its maximum value. For normal operation, the supply voltage (Vsup) should be kept above 2V. In view of its reliability, this D flip flop is a good fit for TR. A D flip flop with 2embedded ports is available. This T flip flop features a maximum design flexibility due to its output current of 8mA. To operate, the chip has a total of 3 output lines.
SN74AHC16374DLR Features
Tape & Reel (TR) package
74AHC series
48 pins
16 Bits
SN74AHC16374DLR Applications
There are a lot of Texas Instruments SN74AHC16374DLR Flip Flops applications.
- Computers
- Dynamic threshold performance
- Buffered Clock
- ESD protection
- Storage Registers
- Balanced 24 mA output drivers
- Supports Live Insertion
- Single Up Count-Control Line
- Communications
- Circuit Design
