SN74AHCT273DWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74AHCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 75MHz |
| Propagation Delay | 9.2 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 9.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| fmax-Min | 65 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 45000000Hz |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT273DWR Overview
20-SOIC (0.295, 7.50mm Width)is the way it is packaged. A package named Tape & Reel (TR)includes it. As configured, the output uses Non-Inverted. It is configured with a trigger that uses Positive Edge. Surface Mountis positioned in the way of this electronic part. The supply voltage is set to 4.5V~5.5V. Temperature is set to -40°C~125°C TA. This logic flip flop is classified as type D-Type. FPGAs belonging to the 74AHCTseries contain this type of chip. Its output frequency should not exceed 75MHz Hz. In total, it contains 1 elements. A total of 20terminations have been recorded. This D latch belongs to the family of 74AHCT273. Power is provided by a 5V supply. A 2.5pFfarad input capacitance is provided by this T flip flop. This D flip flop belongs to the family of AHCT/VHCT/VT. There is an electronic part mounted in the way of Surface Mount. The 20pins are designed into the board. The clock edge trigger type for this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. It is designed with a number of bits of 8. Using 8 circuits, it is highly flexible. Considering the reliability of this T flip flop, it is well suited for TR. The D latch operates on 5V volts. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. A total of 3input lines have been provided. As a result, it consumes 4μA of quiescent current without being affected by external factors.
SN74AHCT273DWR Features
Tape & Reel (TR) package
74AHCT series
20 pins
8 Bits
5V power supplies
SN74AHCT273DWR Applications
There are a lot of Texas Instruments SN74AHCT273DWR Flip Flops applications.
- Communications
- Single Up Count-Control Line
- Digital electronics systems
- Data Synchronizers
- Count Modes
- Supports Live Insertion
- Event Detectors
- Divide a clock signal by 2 or 4
- High Performance Logic for test systems
- Guaranteed simultaneous switching noise level
