SN74AHCT273NSR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 266.712314mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74AHCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 120MHz |
| Propagation Delay | 12.6 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 9.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| fmax-Min | 65 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 45000000Hz |
| Height | 2mm |
| Length | 12.6mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT273NSR Overview
As a result, it is packaged as 20-SOIC (0.209, 5.30mm Width). You can find it in the Tape & Reel (TR)package. T flip flop uses Non-Invertedas the output. It is configured with a trigger that uses a value of Positive Edge. Surface Mountis positioned in the way of this electronic part. It operates with a supply voltage of 4.5V~5.5V. The operating temperature is -40°C~85°C TA. A flip flop of this type is classified as a D-Type. The FPGA belongs to the 74AHCT series. It should not exceed 120MHzin terms of its output frequency. The list contains 1 elements. It consumes 4μA of quiescent current without being affected by external factors. There have been 20 terminations. This D latch belongs to the family of 74AHCT273. An input voltage of 5Vpowers the D latch. This JK flip flop has a 2.5pFfarad input capacitance. This D flip flop belongs to the family of AHCT/VHCT/VT. It is mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This RS flip flops is a part number FF/Latches. Flip flops designed with 8bits are used in this part. The superior flexibility of this circuit is achieved by using 8 circuits. As a result of its reliable performance, this T flip flop is suitable for TR. An electrical current of 5V volts is applied to it. For high efficiency, the supply voltage should be set to 5V. This input has 3lines in it.
SN74AHCT273NSR Features
Tape & Reel (TR) package
74AHCT series
20 pins
8 Bits
5V power supplies
SN74AHCT273NSR Applications
There are a lot of Texas Instruments SN74AHCT273NSR Flip Flops applications.
- Differential Individual
- Pattern generators
- Event Detectors
- Instrumentation
- Clock pulse
- Patented noise
- Consumer
- Buffered Clock
- Automotive
- Memory
