SN74AHCT574DWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74AHCT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 115MHz |
| Propagation Delay | 12.5 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHCT574DWR Overview
The item is packaged in 20-SOIC (0.295, 7.50mm Width)cases. The package Cut Tape (CT)contains it. This output is configured with Tri-State, Non-Inverted. It is configured with a trigger that uses a value of Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 4.5V~5.5V. -40°C~125°C TAis the operating temperature. D-Typeis the type of this D latch. In this case, it is a type of FPGA belonging to the 74AHCT series. Its output frequency should not exceed 115MHz. D latch consists of 1 elements. It consumes 4μA of quiescent A total of 20 terminations have been made. D latch belongs to the 74AHCT574 family. Power is supplied from a voltage of 5V volts. Its input capacitance is 3pF farads. An electronic device belonging to the family AHCT/VHCT/VTcan be found here. Electronic part Surface Mountis mounted in the way. The electronic flip flop is designed with pins 20. A Positive Edgeclock edge trigger is used in this device. There is a FF/Latchesbase part number assigned to the RS flip flops. The flip flop is designed with 8bits. Its flexibility is enhanced by 8 circuits. In light of its reliable performance, this T flip flop is well suited for TR. A total of 5V power supplies are needed to run it. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. It has 3lines.
SN74AHCT574DWR Features
Cut Tape (CT) package
74AHCT series
20 pins
8 Bits
5V power supplies
SN74AHCT574DWR Applications
There are a lot of Texas Instruments SN74AHCT574DWR Flip Flops applications.
- Single Down Count-Control Line
- Count Modes
- Load Control
- QML qualified product
- Parallel data storage
- Consumer
- Dynamic threshold performance
- Bus hold
- Computing
- ATE
