SN74AHCT574PW
| Parameters | |
|---|---|
| Number of Ports | 2 |
| Output Current | 8mA |
| Number of Bits | 8 |
| Clock Frequency | 115MHz |
| Propagation Delay | 12.5 ns |
| Turn On Delay Time | 1 ns |
| Family | AHCT/VHCT/VT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AHCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Termination | SMD/SMT |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74AHCT574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
SN74AHCT574PW Overview
In the form of 20-TSSOP (0.173, 4.40mm Width), it has been packaged. The package Tubecontains it. T flip flop is configured with an output of Tri-State, Non-Inverted. There is a trigger configured with Positive Edge. The electronic part is mounted in the way of Surface Mount. The supply voltage is set to 4.5V~5.5V. The operating temperature is -40°C~85°C TA. D-Typedescribes this flip flop. FPGAs belonging to the 74AHCTseries contain this type of chip. In order for it to function properly, its output frequency should not exceed 115MHz. A total of 1elements are present in it. It consumes 4μA of quiescent current without being affected by external factors. There have been 20 terminations. It is a member of the 74AHCT574 family. The D flip flop is powered by a voltage of 5V . The input capacitance of this JK flip flopis 3pF farads. A device of this type belongs to the family of AHCT/VHCT/VT. This electronic part is mounted in the way of Surface Mount. With its 20pins, it is designed to work with most electronic flip flops. Its clock edge trigger type is Positive Edge. The part you are looking for is included in FF/Latches. The flip flop is designed with 8bits. 8 circuits are used to achieve its superior flexibility. A power supply of 5Vis required to operate it. This D flip flop is equipped with 0 ports. The supply voltage should be maintained at 5V for high efficiency. Its output current of 8mAallows for maximum design flexibility. The number of input lines is 3.
SN74AHCT574PW Features
Tube package
74AHCT series
20 pins
8 Bits
5V power supplies
SN74AHCT574PW Applications
There are a lot of Texas Instruments SN74AHCT574PW Flip Flops applications.
- Control circuits
- Patented noise
- Clock pulse
- Cold spare funcion
- ATE
- Shift Registers
- 2 – Bit synchronous counter
- Load Control
- Instrumentation
- Convert a momentary switch to a toggle switch
