SN74ALS273DWE4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74ALS |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latch |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ALS273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 35MHz |
| Propagation Delay | 18 ns |
| Turn On Delay Time | 2 ns |
| Family | ALS |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 20mA |
| Current - Output High, Low | 2.6mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 15ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Power Supply Current-Max (ICC) | 29mA |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ALS273DWE4 Overview
The package is in the form of 20-SOIC (0.295, 7.50mm Width). D flip flop is embedded in the Tube package. T flip flop uses Non-Invertedas the output. Positive Edgeis the trigger it is configured with. Surface Mountis in the way of this electric part. With a supply voltage of 4.5V~5.5V volts, it operates. 0°C~70°C TAis the operating temperature. This logic flip flop is classified as type D-Type. In this case, it is a type of FPGA belonging to the 74ALS series. Its output frequency should not exceed 35MHz Hz. There are 1 elements in it. As a result, it consumes 20mA quiescent current. Terminations are 20. It is a member of the 74ALS273 family. It is powered by a voltage of 5V . Electronic devices of this type belong to the ALSfamily. The electronic part is mounted in the way of Surface Mount. There are 20pins on it. In this device, the clock edge trigger type is Positive Edge. The part you are looking for is included in FF/Latch. Flip flops designed with 8bits are used in this part. The superior flexibility of this circuit is achieved by using 8 circuits. It runs on 5Vvolts of power. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. It offers maximum design flexibility with its output current of 24mA. This input has 3lines in it.
SN74ALS273DWE4 Features
Tube package
74ALS series
20 pins
8 Bits
5V power supplies
SN74ALS273DWE4 Applications
There are a lot of Texas Instruments SN74ALS273DWE4 Flip Flops applications.
- Balanced 24 mA output drivers
- Memory
- Storage registers
- ESCC
- Data transfer
- Synchronous counter
- Guaranteed simultaneous switching noise level
- Set-reset capability
- Parallel data storage
- Divide a clock signal by 2 or 4
