SN74ALVCH16374KR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 56-VFBGA |
| Number of Pins | 56 |
| Weight | 58.796911mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ALVCH |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 56 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 1.65V~3.6V |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ALVCH16374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 1.65V |
| Number of Ports | 2 |
| Number of Bits | 16 |
| Clock Frequency | 150MHz |
| Propagation Delay | 4.9 ns |
| Turn On Delay Time | 1 ns |
| Family | ALVC/VCX/A |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 40μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 4.2ns @ 3.3V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 150000000Hz |
| Height Seated (Max) | 1mm |
| Length | 7mm |
| Width | 4.5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
SN74ALVCH16374KR Overview
The item is packaged in 56-VFBGAcases. You can find it in the Cut Tape (CT)package. T flip flop uses Tri-State, Non-Invertedas its output configuration. The trigger it is configured with uses Positive Edge. The electronic part is mounted in the way of Surface Mount. It operates with a supply voltage of 1.65V~3.6V. It is at -40°C~85°C TAdegrees Celsius that the system is operating. There is D-Type type of electronic flip flop associated with this device. This type of FPGA is a part of the 74ALVCH series. You should not exceed 150MHzin its output frequency. In total, it contains 2 elements. T flip flop consumes 40μA quiescent energy. In 56terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. You can search similar parts based on 74ALVCH16374. It is powered by a voltage of 1.8V . A 3pFfarad input capacitance is provided by this T flip flop. In this case, the D flip flop belongs to the ALVC/VCX/Afamily. It is mounted by the way of Surface Mount. The electronic flip flop is designed with pins 56. A Positive Edgeclock edge trigger is used in this device. The RS flip flops belongs to FF/Latches base part number. An electronic part with 16bits has been designed. It is imperative that the supply voltage (Vsup) is maintained above 1.65Vin order to ensure normal operation. Considering its reliability, this T flip flop is well suited for TAPE AND REEL. The D flip flop is embedded with 2ports. In order to operate, the chip has 3 output lines.
SN74ALVCH16374KR Features
Cut Tape (CT) package
74ALVCH series
56 pins
16 Bits
SN74ALVCH16374KR Applications
There are a lot of Texas Instruments SN74ALVCH16374KR Flip Flops applications.
- Computers
- Buffer registers
- Bounce elimination switch
- Load Control
- Control circuits
- Power down protection
- Frequency Dividers
- Divide a clock signal by 2 or 4
- Frequency division
- Parallel data storage
