SN74AS823ADW
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 24 |
| Weight | 624.398247mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74AS |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | WITH CLEAR AND CLOCK ENABLE |
| Subcategory | FF/Latches |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74AS823 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Ports | 2 |
| Output Current | 48mA |
| Propagation Delay | 13 ns |
| Turn On Delay Time | 3.5 ns |
| Family | AS |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 80mA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 24mA 48mA |
| Number of Bits per Element | 9 |
| Max Propagation Delay @ V, Max CL | 13ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Number of Input Lines | 5 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
SN74AS823ADW Overview
The flip flop is packaged in 24-SOIC (0.295, 7.50mm Width). As part of the package Tube, it is embedded. T flip flop is configured with an output of Tri-State, Non-Inverted. In the configuration of the trigger, Positive Edgeis used. Surface Mountis in the way of this electric part. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. It is operating at a temperature of 0°C~70°C TA. This logic flip flop is classified as type D-Type. It belongs to the 74ASseries of FPGAs. A total of 1elements are contained within it. As a result, it consumes 80mA quiescent current. A total of 24 terminations have been made. It is a member of the 74AS823 family. A voltage of 5V is used as the power supply for this D latch. In this case, the D flip flop belongs to the ASfamily. The electronic part is mounted in the way of Surface Mount. A total of 24pins are provided on this board. Its clock edge trigger type is Positive Edge. This device is part of the FF/Latchesbase part number family. The flip flop has 2ports embedded within it. For high efficiency, the supply voltage should be set to 5V. This T flip flop features a maximum design flexibility due to its output current of 48mA. This input has 5lines in it. Additionally, you may refer to the additional WITH CLEAR AND CLOCK ENABLE of the electronic flip flop.
SN74AS823ADW Features
Tube package
74AS series
24 pins
SN74AS823ADW Applications
There are a lot of Texas Instruments SN74AS823ADW Flip Flops applications.
- ESCC
- CMOS Process
- Data storage
- Modulo – n – counter
- Single Up Count-Control Line
- EMI reduction circuitry
- Guaranteed simultaneous switching noise level
- High Performance Logic for test systems
- Divide a clock signal by 2 or 4
- Bounce elimination switch
