SN74AS874NT
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 24-DIP (0.300, 7.62mm) |
| Number of Pins | 24 |
| Weight | 1.753503g |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74AS |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | WITH CLEAR |
| Subcategory | FF/Latches |
| Technology | TTL |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Base Part Number | 74AS874 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 48mA |
| Number of Bits | 8 |
| Clock Frequency | 125MHz |
| Propagation Delay | 10.5 ns |
| Turn On Delay Time | 3 ns |
| Family | AS |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 133mA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 15mA 48mA |
| Number of Bits per Element | 4 |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AS874NT Overview
The flip flop is packaged in a case of 24-DIP (0.300, 7.62mm). As part of the package Tube, it is embedded. The output it is configured with uses Tri-State, Non-Inverted. The trigger configured with it uses Positive Edge. It is mounted in the way of Through Hole. The JK flip flop operates at a voltage of 4.5V~5.5V. In this case, the operating temperature is 0°C~70°C TA. This electronic flip flop is of type D-Type. FPGAs belonging to the 74ASseries contain this type of chip. This D flip flop should not have a frequency greater than 125MHz. A total of 2elements are present in it. T flip flop consumes 133mA quiescent energy. A total of 24terminations have been recorded. You can search similar parts based on 74AS874. Power is provided by a 5V supply. The electronic device belongs to the ASfamily. Through Hole mounts this electronic component. The 24pins are designed into the board. A Positive Edgeclock edge trigger is used in this device. It is included in FF/Latches. Flip flops designed with 8bits are used in this part. A total of 5V power supplies are needed to run it. The D flip flop has no ports embedded. If high efficiency is desired, the supply voltage should be kept at 5V. The 48mA output current allows it to be designed with the greatest amount of flexibility. There are 1 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code. As an additional reference, you may refer to electronic flip flop WITH CLEAR.
SN74AS874NT Features
Tube package
74AS series
24 pins
8 Bits
5V power supplies
SN74AS874NT Applications
There are a lot of Texas Instruments SN74AS874NT Flip Flops applications.
- Reduced system switching noise
- Single Up Count-Control Line
- Digital electronics systems
- Balanced 24 mA output drivers
- QML qualified product
- Computers
- Counters
- Convert a momentary switch to a toggle switch
- Frequency Dividers
- Data Synchronizers
