SN74AUP1G80DBVTG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 11.198062mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AUP |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 0.8V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 1.2V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AUP1G80 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Inverted |
| Polarity | Inverting |
| Supply Voltage-Max (Vsup) | 3.6V |
| Supply Voltage-Min (Vsup) | 0.8V |
| Number of Circuits | 1 |
| Load Capacitance | 30pF |
| Number of Bits | 1 |
| Clock Frequency | 260MHz |
| Propagation Delay | 20.7 ns |
| Turn On Delay Time | 3.1 ns |
| Family | AUP/ULP/V |
| Current - Quiescent (Iq) | 0.9μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 6.4ns @ 3.3V, 30pF |
| Prop. Delay@Nom-Sup | 28.7 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 1.5pF |
| Power Supply Current-Max (ICC) | 0.0009mA |
| fmax-Min | 260 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 260000000Hz |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AUP1G80DBVTG4 Overview
In the form of SC-74A, SOT-753, it has been packaged. It is contained within the Tape & Reel (TR)package. There is a Invertedoutput configured with it. Positive Edgeis the trigger it is configured with. This electronic part is mounted in the way of Surface Mount. The supply voltage is set to 0.8V~3.6V. In the operating environment, the temperature is -40°C~85°C TA. This logic flip flop is classified as type D-Type. This type of FPGA is a part of the 74AUP series. There should be no greater frequency than 260MHzon its output. During its operation, it consumes 0.9μA quiescent energy. In 5terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. If you search by 74AUP1G80, you will find similar parts. The power source is powered by 1.2V. Its input capacitance is 1.5pFfarads. It belongs to the family of electronic devices known as AUP/ULP/V. There is an electronic component mounted in the way of Surface Mount. With its 5pins, it is designed to work with most electronic flip flops. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The part is included in FF/Latches. An electronic part designed with 1bits is used in this application. In this case, the maximum supply voltage (Vsup) reaches 3.6V. It is imperative that the supply voltage (Vsup) is maintained above 0.8Vin order to ensure normal operation. Its flexibility is enhanced by 1 circuits. In view of its reliability, this D flip flop is a good fit for TR.
SN74AUP1G80DBVTG4 Features
Tape & Reel (TR) package
74AUP series
5 pins
1 Bits
SN74AUP1G80DBVTG4 Applications
There are a lot of Texas Instruments SN74AUP1G80DBVTG4 Flip Flops applications.
- Set-reset capability
- Dynamic threshold performance
- Count Modes
- Load Control
- Data transfer
- Power down protection
- Balanced Propagation Delays
- Pattern generators
- Storage registers
- Patented noise
