SN74F175DRE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Subcategory | FF/Latch |
| Packing Method | TAPE AND REEL |
| Technology | TTL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Frequency | 140MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Current - Output | 20mA |
| Propagation Delay | 8.5 ns |
| Turn On Delay Time | 3.2 ns |
| Family | F/FAST |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.02 A |
| Number of Bits per Element | 4 |
| High Level Output Current | -1mA |
| Low Level Output Current | 20mA |
| Clock Edge Trigger Type | Positive Edge |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74F175DRE4 Overview
SOICis the packaging method. You can find it in the Tape & Reel (TR)package. T flip flop is configured with an output of TTL. A total of 1 elements are present. In 16terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. It is powered from a supply voltage of 5V. A device of this type belongs to the family of F/FAST. There is an electronic part mounted in the way of Surface Mount. With its 16pins, it is designed to work with most electronic flip flops. This device has the clock edge trigger type of Positive Edge. It is included in FF/Latch. In light of its reliable performance, this T flip flop is well suited for TAPE AND REEL. An electrical current of 5V volts is applied to it. High efficiency requires the supply voltage to be maintained at 5V. -1mAis set as the high level output current. In the low level output current setting, 20mAis used. Temperatures below 70°Care ideal for operating. Ideally, the operating temperature should be greater than 0°C. Normally, it operates with a voltage of 4.5VV as its minimum supply voltage. 5.5Vis the maximum supply voltage supported by it. This can be achieved at a frequency of 140MHz. In this case, it uses a D FLIP-FLOP logic IC. Currently, it is equipped with 4 functions . There are 16 pins on the D latch. Its output current of 20mA allows for maximum design flexibility.
SN74F175DRE4 Features
Tape & Reel (TR) package
16 pins
5V power supplies
4 Functions
16 pin count
SN74F175DRE4 Applications
There are a lot of Texas Instruments SN74F175DRE4 Flip Flops applications.
- Balanced Propagation Delays
- Communications
- Cold spare funcion
- Bus hold
- Memory
- Latch-up performance
- Circuit Design
- Clock pulse
- Counters
- Set-reset capability
