SN74HC109N
| Parameters | |
|---|---|
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 2 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Clock Frequency | 60MHz |
| Propagation Delay | 175 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 12 ns |
| Family | HC/UH |
| Logic Function | AND, Flip-Flop, JK-Type |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.004 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 30ns @ 6V, 50pF |
| Prop. Delay@Nom-Sup | 58 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Schmitt Trigger | No |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 951.693491mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | JK Type |
| Additional Feature | DUMMY VAL |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Base Part Number | 74HC109 |
| Function | Set(Preset) and Reset |
SN74HC109N Overview
The flip flop is packaged in a case of 16-DIP (0.300, 7.62mm). There is an embedded version in the package Tube. Currently, the output is configured to use Differential. It is configured with a trigger that uses a value of Positive Edge. There is an electric part mounted in the way of Through Hole. The supply voltage is set to 2V~6V. A temperature of -40°C~85°C TAis used in the operation. This electronic flip flop is of type JK Type. JK flip flop is a part of the 74HCseries of FPGAs. It should not exceed 60MHzin its output frequency. A total of 16terminations have been recorded. D latch belongs to the 74HC109 family. An input voltage of 5Vpowers the D latch. Input capacitance of this device is 3pF farads. It is a member of the HC/UHfamily of D flip flop. Through Hole mounts this electronic component. This board is designed with 16pins on it. There is a clock edge trigger type of Positive Edgeon this device. The part is included in FF/Latches. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. For normal operation, the supply voltage (Vsup) should be above 2V. For high efficiency, the supply voltage should be set to 5V. With an output current of 5.2mA, this device offers maximum design flexibility. It has 3 output lines to operate. It consumes 4μA of quiescent current without being affected by external factors. Furthermore, it has DUMMY VALas a characteristic. 2 channels are available.
SN74HC109N Features
Tube package
74HC series
16 pins
SN74HC109N Applications
There are a lot of Texas Instruments SN74HC109N Flip Flops applications.
- Dynamic threshold performance
- Shift registers
- QML qualified product
- Automotive
- Single Down Count-Control Line
- Reduced system switching noise
- Event Detectors
- Frequency Dividers
- 2 – Bit synchronous counter
- Memory
