SN74HC174N
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 951.693491mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | 74HC174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 6 |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Number of Bits | 6 |
| Clock Frequency | 50MHz |
| Propagation Delay | 160 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 14 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.0052 A |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 50pF |
| Prop. Delay@Nom-Sup | 40 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Power Supply Current-Max (ICC) | 0.08mA |
| Number of Input Lines | 3 |
| fmax-Min | 29 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 25000000Hz |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC174N Overview
The item is packaged in 16-DIP (0.300, 7.62mm)cases. As part of the package Tube, it is embedded. It is configured with Non-Invertedas an output. Positive Edgeis the trigger it is configured with. There is an electrical part that is mounted in the way of Through Hole. A voltage of 2V~6Vis required for its operation. A temperature of -40°C~85°C TAis used in the operation. This electronic flip flop is of type D-Type. JK flip flop belongs to the 74HCseries of FPGAs. This D flip flop should not have a frequency greater than 50MHz. A total of 1elements are present in it. Terminations are 16. You can search similar parts based on 74HC174. The power supply voltage is 5V. The input capacitance of this T flip flop is 3pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. A device of this type belongs to the family of HC/UH. A part of the electronic system is mounted in the way of Through Hole. The electronic flip flop is designed with pins 16. This device has Positive Edgeas its clock edge trigger type. It is included in FF/Latches. An electronic part with 6bits has been designed. It reaches the maximum supply voltage (Vsup) at 6V. Keeping the supply voltage (Vsup) above 2V is necessary for normal operation. In order to achieve its superior flexibility, 7 circuits are used. In order to ensure high efficiency, the supply voltage should remain at 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 5.2mA. This input has 3lines in it. 8μAquiescent current consumed. The number of channels is growing strong/weak: 6.
SN74HC174N Features
Tube package
74HC series
16 pins
6 Bits
SN74HC174N Applications
There are a lot of Texas Instruments SN74HC174N Flip Flops applications.
- Synchronous counter
- Circuit Design
- Count Modes
- Matched Rise and Fall
- Single Up Count-Control Line
- Modulo – n – counter
- Communications
- Divide a clock signal by 2 or 4
- Data storage
- Latch-up performance
