SN74HC175N
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 951.693491mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Supply Voltage | 5V |
| Base Part Number | 74HC175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 4 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Number of Bits | 4 |
| Clock Frequency | 60MHz |
| Propagation Delay | 190 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 26ns @ 6V, 50pF |
| Prop. Delay@Nom-Sup | 38 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Power Supply Current-Max (ICC) | 0.08mA |
| Number of Output Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC175N Overview
The item is packaged in 16-DIP (0.300, 7.62mm)cases. D flip flop is included in the Tubepackage. T flip flop uses Differentialas the output. It is configured with a trigger that uses a value of Positive Edge. This electronic part is mounted in the way of Through Hole. A 2V~6Vsupply voltage is required for it to operate. -40°C~85°C TAis the operating temperature. Logic flip flops of this type are classified as D-Type. It is a type of FPGA belonging to the 74HC series. This D flip flop should not have a frequency greater than 60MHz. In total, it contains 1 elements. The number of terminations is 16. The object belongs to the 74HC175 family. The power supply voltage is 5V. The input capacitance of this T flip flop is 3pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. In this case, the D flip flop belongs to the HC/UHfamily. There is an electronic component mounted in the way of Through Hole. This board is designed with 16pins on it. Its clock edge trigger type is Positive Edge. This device has the base part number FF/Latches. This flip flop is designed with 4 Bits. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. If you want to maintain normal operation, you should keep the supply voltage (Vsup) above 2V. For high efficiency, the supply voltage should be kept at 5V. The 5.2mA output current allows it to be designed with the greatest amount of flexibility. The JK flip flop is with 2 output lines to operate. In terms of quiescent current, it consumes 8μA . Currently, there are 4 channels available.
SN74HC175N Features
Tube package
74HC series
16 pins
4 Bits
SN74HC175N Applications
There are a lot of Texas Instruments SN74HC175N Flip Flops applications.
- Safety Clamp
- Set-reset capability
- Asynchronous counter
- Patented noise
- Dynamic threshold performance
- Cold spare funcion
- Load Control
- Guaranteed simultaneous switching noise level
- 2 – Bit synchronous counter
- Common Clocks
