SN74HC273NSR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 266.712314mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Additional Feature | DUMMY VAL |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 25mA |
| Number of Bits | 8 |
| Clock Frequency | 60MHz |
| Propagation Delay | 200 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 27ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2mm |
| Length | 12.6mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC273NSR Overview
The flip flop is packaged in a case of 20-SOIC (0.209, 5.30mm Width). D flip flop is included in the Cut Tape (CT)package. T flip flop uses Non-Invertedas its output configuration. This trigger uses the value Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. A supply voltage of 2V~6V is required for operation. In the operating environment, the temperature is -40°C~85°C TA. This D latch has the type D-Type. In this case, it is a type of FPGA belonging to the 74HC series. You should not exceed 60MHzin its output frequency. D latch consists of 1 elements. Terminations are 20. The object belongs to the 74HC273 family. Power is supplied from a voltage of 5V volts. Its input capacitance is 3pF farads. Devices in the HC/UHfamily are electronic devices. There is an electronic part that is mounted in the way of Surface Mount. 20pins are included in its design. The clock edge trigger type for this device is Positive Edge. This device is part of the FF/Latchesbase part number family. The flip flop is designed with 8bits. 6Vis the maximum supply voltage (Vsup). Keeping the supply voltage (Vsup) above 2V is necessary for normal operation. Its flexibility is enhanced by 8 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TR. High efficiency requires the supply voltage to be maintained at 5V. This T flip flop features a maximum design flexibility due to its output current of 25mA. It is reported that there are 2 input lines. It consumes a total of 8μA quiescent current at any given time. DUMMY VALis also one of its characteristics.
SN74HC273NSR Features
Cut Tape (CT) package
74HC series
20 pins
8 Bits
SN74HC273NSR Applications
There are a lot of Texas Instruments SN74HC273NSR Flip Flops applications.
- Balanced 24 mA output drivers
- Single Up Count-Control Line
- Power down protection
- Convert a momentary switch to a toggle switch
- Buffer registers
- Bus hold
- Divide a clock signal by 2 or 4
- Functionally equivalent to the MC10/100EL29
- Parallel data storage
- Memory
