SN74HC574DWRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HC574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 7.8mA |
| Number of Bits | 8 |
| Clock Frequency | 40MHz |
| Propagation Delay | 265 ns |
| Turn On Delay Time | 24 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 31ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 24000000Hz |
| Height | 2.35mm |
| Length | 12.8mm |
| Width | 7.52mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
SN74HC574DWRG4 Overview
The package is in the form of 20-SOIC (0.295, 7.50mm Width). D flip flop is embedded in the Tape & Reel (TR) package. T flip flop uses Tri-State, Non-Invertedas the output. There is a trigger configured with Positive Edge. There is an electric part mounted in the way of Surface Mount. The supply voltage is set to 2V~6V. It is operating at -40°C~85°C TA. The type of this D latch is D-Type. In FPGA terms, D flip flop is a type of 74HCseries FPGA. Its output frequency should not exceed 40MHz Hz. The element count is 1 . As a result, it consumes 8μA of quiescent current without being affected by external factors. A total of 20terminations have been recorded. JK flip flop belongs to 74HC574 family. It is powered from a supply voltage of 5V. There is 3pF input capacitance for this T flip flop. Devices in the HC/UHfamily are electronic devices. There is an electronic part that is mounted in the way of Surface Mount. 20pins are included in its design. This device exhibits a clock edge trigger type of Positive Edge. It is part of the FF/Latchesbase part number family. It is designed with a number of bits of 8. It reaches 6Vwhen the supply voltage is maximal (Vsup). For normal operation, the supply voltage (Vsup) should be above 2V. The superior flexibility is achieved through the use of 8 circuits. Considering its reliability, this T flip flop is well suited for TAPE AND REEL. The power supply is 2/6V. The flip flop contains 2ports. High efficiency requires the supply voltage to be maintained at 5V. As a result of its output current of 7.8mA, it is very flexible in terms of design. 3input lines are available for you to choose from.
SN74HC574DWRG4 Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
2/6V power supplies
SN74HC574DWRG4 Applications
There are a lot of Texas Instruments SN74HC574DWRG4 Flip Flops applications.
- Consumer
- Buffered Clock
- Data storage
- Frequency Dividers
- Reduced system switching noise
- ESD performance
- Asynchronous counter
- Storage Registers
- Counters
- Shift Registers
