SN74HC574PWRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 7.8mA |
| Number of Bits | 8 |
| Clock Frequency | 40MHz |
| Propagation Delay | 265 ns |
| Turn On Delay Time | 24 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max Propagation Delay @ V, Max CL | 31ns @ 6V, 50pF |
| Prop. Delay@Nom-Sup | 0.066 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 24000000Hz |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC574PWRG4 Overview
The flip flop is packaged in a case of 20-TSSOP (0.173, 4.40mm Width). A package named Tape & Reel (TR)includes it. As configured, the output uses Tri-State, Non-Inverted. The trigger configured with it uses Positive Edge. Surface Mountis in the way of this electric part. A 2V~6Vsupply voltage is required for it to operate. It is operating at -40°C~85°C TA. D-Typedescribes this flip flop. It is a type of FPGA belonging to the 74HC series. It should not exceed 40MHzin terms of its output frequency. In total, it contains 1 elements. During its operation, it consumes 8μA quiescent energy. It has been determined that there have been 20 terminations. It is a member of the 74HC574 family. An input voltage of 5Vpowers the D latch. A JK flip flop with a 3pFfarad input capacitance is used here. A device of this type belongs to the family of HC/UH. It is mounted by the way of Surface Mount. There are 20pins on it. This device has Positive Edgeas its clock edge trigger type. It is included in FF/Latches. An electronic part designed with 8bits is used in this application. It reaches 6Vwhen the supply voltage is maximal (Vsup). If you want to maintain normal operation, you should keep the supply voltage (Vsup) above 2V. The superior flexibility of this circuit is achieved by using 8 circuits. As a result of its reliability, this D flip flop is ideally suited for TR. The D latch operates on 2/6V volts. There are 2 ports embedded in the flip flops. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. It offers maximum design flexibility with its output current of 7.8mA. This input has 3lines in it.
SN74HC574PWRG4 Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
2/6V power supplies
SN74HC574PWRG4 Applications
There are a lot of Texas Instruments SN74HC574PWRG4 Flip Flops applications.
- Guaranteed simultaneous switching noise level
- Circuit Design
- Balanced 24 mA output drivers
- Buffered Clock
- Test & Measurement
- Balanced Propagation Delays
- Single Down Count-Control Line
- Data storage
- Count Modes
- Pattern generators
