SN74HC74DBR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 14 |
| Weight | 121.789551mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Clock Frequency | 60MHz |
| Propagation Delay | 290 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 30ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2mm |
| Length | 6.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HC74DBR Overview
It is embeded in 14-SSOP (0.209, 5.30mm Width) case. It is included in the package Cut Tape (CT). T flip flop is configured with an output of Differential. In the configuration of the trigger, Positive Edgeis used. The electronic part is mounted in the way of Surface Mount. The supply voltage is set to 2V~6V. It is operating at a temperature of -40°C~85°C TA. A flip flop of this type is classified as a D-Type. FPGAs belonging to the 74HCseries contain this type of chip. Its output frequency should not exceed 60MHz Hz. It has been determined that there have been 14 terminations. You can search similar parts based on 74HC74. The power supply voltage is 5V. The input capacitance of this T flip flop is 3pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. It is a member of the HC/UHfamily of D flip flop. This electronic part is mounted in the way of Surface Mount. It is designed with 14 pins. It has a clock edge trigger type of Positive Edge. This device has the base part number FF/Latches. There is a 6Vmaximum supply voltage (Vsup). Normally, the supply voltage (Vsup) should be kept above 2V. The superior flexibility of this product is achieved by using 2 circuits. In light of its reliable performance, this T flip flop is well suited for TR. In order to ensure high efficiency, the supply voltage should remain at 5V. With a current output of 5.2mA , it offers maximum design flexibility. 4input lines are available for you to choose from. There is a consumption of 4μAof quiescent current from it.
SN74HC74DBR Features
Cut Tape (CT) package
74HC series
14 pins
SN74HC74DBR Applications
There are a lot of Texas Instruments SN74HC74DBR Flip Flops applications.
- Consumer
- Patented noise
- Safety Clamp
- Storage registers
- Communications
- Bounce elimination switch
- Convert a momentary switch to a toggle switch
- Count Modes
- Data Synchronizers
- Matched Rise and Fall
