SN74HC74DT
| Parameters | |
|---|---|
| Base Part Number | 74HC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Clock Frequency | 60MHz |
| Propagation Delay | 290 ns |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 30ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
SN74HC74DT Overview
14-SOIC (0.154, 3.90mm Width)is the way it is packaged. As part of the package Tape & Reel (TR), it is embedded. It is configured with Differentialas an output. It is configured with a trigger that uses Positive Edge. There is an electric part mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 2V~6V volts. A temperature of -40°C~85°C TAis considered to be the operating temperature. This D latch has the type D-Type. FPGAs belonging to the 74HCseries contain this type of chip. Its output frequency should not exceed 60MHz. As a result, it consumes 4μA of quiescent current without being affected by external factors. The number of terminations is 14. It is a member of the 74HC74 family. Power is supplied from a voltage of 5V volts. Its input capacitance is 3pF farads. In this case, the D flip flop belongs to the HC/UHfamily. In this case, the electronic component is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 14. This device has Positive Edgeas its clock edge trigger type. The part you are looking for is included in FF/Latches. There is a 6Vmaximum supply voltage (Vsup). Normal operation requires a supply voltage (Vsup) above 2V. To achieve this superior flexibility, 2 circuits are used. Considering the reliability of this T flip flop, it is well suited for TR. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. The 5.2mA output current allows it to be designed with the greatest amount of flexibility. The number of input lines is 4.
SN74HC74DT Features
Tape & Reel (TR) package
74HC series
14 pins
SN74HC74DT Applications
There are a lot of Texas Instruments SN74HC74DT Flip Flops applications.
- Digital electronics systems
- Frequency Dividers
- Test & Measurement
- Asynchronous counter
- Balanced 24 mA output drivers
- Matched Rise and Fall
- Bounce elimination switch
- Buffered Clock
- 2 – Bit synchronous counter
- Shift Registers
