SN74HC74PWG4
| Parameters | |
|---|---|
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 5.2mA |
| Clock Frequency | 60MHz |
| Propagation Delay | 175 ns |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 30ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74HC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
SN74HC74PWG4 Overview
The item is packaged in 14-TSSOP (0.173, 4.40mm Width)cases. It is included in the package Tube. It is configured with Differentialas an output. JK flip flop uses Positive Edgeas the trigger. There is an electronic component mounted in the way of Surface Mount. A 2V~6Vsupply voltage is required for it to operate. A temperature of -40°C~85°C TAis used in the operation. D-Typedescribes this flip flop. It belongs to the 74HCseries of FPGAs. Its output frequency should not exceed 60MHz. During its operation, it consumes 4μA quiescent energy. There are 14 terminations,It is a member of the 74HC74 family. It is powered from a supply voltage of 5V. Its input capacitance is 3pFfarads. Electronic devices of this type belong to the HC/UHfamily. The electronic part is mounted in the way of Surface Mount. This board has 14 pins. This device has Positive Edgeas its clock edge trigger type. The RS flip flops belongs to FF/Latches base part number. Vsup reaches its maximum value at 6V. A normal operating voltage (Vsup) should remain above 2V. Using 2 circuits, it is highly flexible. For high efficiency, the supply voltage should be kept at 5V. As a result of its output current of 5.2mA, it is very flexible in terms of design. There are 4 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply.
SN74HC74PWG4 Features
Tube package
74HC series
14 pins
SN74HC74PWG4 Applications
There are a lot of Texas Instruments SN74HC74PWG4 Flip Flops applications.
- Reduced system switching noise
- Set-reset capability
- Shift Registers
- Frequency division
- Single Down Count-Control Line
- Balanced Propagation Delays
- Load Control
- Test & Measurement
- Control circuits
- Frequency Divider circuits
