SN74HCT273DBR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HCT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 37MHz |
| Propagation Delay | 42 ns |
| Turn On Delay Time | 15 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 29ns @ 5.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HCT273DBR Overview
It is packaged in the way of 20-SSOP (0.209, 5.30mm Width). A package named Cut Tape (CT)includes it. It is configured with Non-Invertedas an output. It is configured with a trigger that uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 4.5V~5.5V. It is operating at a temperature of -40°C~85°C TA. This D latch has the type D-Type. JK flip flop is a part of the 74HCTseries of FPGAs. Its output frequency should not exceed 37MHz. In total, there are 1 elements. There is a consumption of 8μAof quiescent energy. A total of 20 terminations have been made. This D latch belongs to the family of 74HCT273. A voltage of 5V is used to power it. Input capacitance of this device is 3pF farads. The electronic device belongs to the HCTfamily. In this case, the electronic component is mounted in the way of Surface Mount. Basically, it is designed with a set of 20 pins. Its clock edge trigger type is Positive Edge. This part is included in FF/Latches. This flip flop is designed with 8 Bits. Its flexibility is enhanced by 8 circuits. Considering the reliability of this T flip flop, it is well suited for TR. It runs on 5Vvolts of power. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. Currently, there are 3 input lines present.
SN74HCT273DBR Features
Cut Tape (CT) package
74HCT series
20 pins
8 Bits
5V power supplies
SN74HCT273DBR Applications
There are a lot of Texas Instruments SN74HCT273DBR Flip Flops applications.
- CMOS Process
- Count Modes
- Load Control
- Set-reset capability
- Frequency division
- Differential Individual
- Data Synchronizers
- Computing
- Divide a clock signal by 2 or 4
- Bus hold
