SN74HCT374DWRE4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 40MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 46 ns |
| Turn On Delay Time | 25 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.006 A |
| Prop. Delay@Nom-Sup | 45 ns |
| High Level Output Current | -6mA |
| Low Level Output Current | 6mA |
| Control Type | ENABLE LOW |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74HCT374DWRE4 Overview
SOICis the way it is packaged. The Tape & Reel (TR)package contains it. A total of 20terminations have been recorded. The power supply voltage is 5V. In this case, the D flip flop belongs to the HCTfamily. Surface Mount mounts this electronic component. With its 20pins, it is designed to work with most electronic flip flops. In this device, the clock edge trigger type is Positive Edge. The RS flip flops belongs to FF/Latches base part number. The flip flop is designed with 8bits. The superior flexibility is achieved through the use of 8 circuits. As a result of its reliable performance, this T flip flop is suitable for TR. An electrical current of 5V volts is applied to it. The flip flop has 2embedded ports. For high efficiency, the supply voltage should be kept at 5V. In order to operate, the chip has 1 output lines. This input has 3lines in it. -6mAis set as the high level output current. There is no low level output current set at 6mA. Ideally, the operating temperature should be lower than 85°C. A temperature above -40°Cshould be used for the operation. Despite its minimal supply voltage of 4.5V, it is capable of operating. It is capable of supporting a maximum supply voltage of 5.5V. The frequency that can be achieved is 40MHz. There is a logic IC BUS DRIVER used in the D flip flop. There are 1 functions available on this T flip flop. 20pins are available on this JK flip flop.
SN74HCT374DWRE4 Features
Tape & Reel (TR) package
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
SN74HCT374DWRE4 Applications
There are a lot of Texas Instruments SN74HCT374DWRE4 Flip Flops applications.
- Matched Rise and Fall
- Guaranteed simultaneous switching noise level
- CMOS Process
- Buffer registers
- Supports Live Insertion
- Instrumentation
- Event Detectors
- Single Down Count-Control Line
- Balanced 24 mA output drivers
- Consumer
