SN74HCT374NSRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOP |
| Number of Pins | 20 |
| Weight | 266.712314mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 40MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Propagation Delay | 46 ns |
| Turn On Delay Time | 25 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.006 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -6mA |
| Low Level Output Current | 6mA |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2mm |
| Width | 5.3mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74HCT374NSRG4 Overview
It is packaged in the way of SOP. It is contained within the Tape & Reel (TR)package. In total, it contains 1 elements. There are 20 terminations,The D flip flop is powered by a voltage of 5V . It belongs to the family of electronic devices known as HCT. It is mounted by the way of Surface Mount. 20pins are included in its design. It has a clock edge trigger type of Positive Edge. This RS flip flops is a part number FF/Latches. In view of its reliability, this D flip flop is a good fit for TAPE AND REEL. A total of 5V power supplies are needed to run it. A total of 2ports are embedded in the D flip flop. For high efficiency, the supply voltage should be set to 5V. -6mAis the output current at high level. It is set to 6mAfor the low level output current. If the operating temperature is lower than 85°C, it is recommended. Ideally, the operating temperature should be higher than -40°C. It is powered by 4.5V as its minimum supply voltage. It supports the maximal supply voltage of 5.5V. A frequency of 40MHzcan be achieved. BUS DRIVERis used as the logic IC in this D flip flop. There are 1 functions associated with the JK flip flop. It is equipped with 20 pins.
SN74HCT374NSRG4 Features
Tape & Reel (TR) package
20 pins
5V power supplies
1 Functions
20 pin count
SN74HCT374NSRG4 Applications
There are a lot of Texas Instruments SN74HCT374NSRG4 Flip Flops applications.
- Control circuits
- Cold spare funcion
- Power down protection
- Registers
- Parallel data storage
- Data storage
- Matched Rise and Fall
- Functionally equivalent to the MC10/100EL29
- Computing
- Supports Live Insertion
