SN74HCT574DWRG4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 40MHz |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Propagation Delay | 53 ns |
| Turn On Delay Time | 25 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.006 A |
| Number of Bits per Element | 8 |
| Prop. Delay@Nom-Sup | 45 ns |
| High Level Output Current | -6mA |
| Low Level Output Current | 6mA |
| Control Type | ENABLE LOW |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74HCT574DWRG4 Overview
SOICis the way it is packaged. The list contains 1 elements. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. An input voltage of 5Vpowers the D latch. HCTis the family of this D flip flop. There is an electronic part mounted in the way of Surface Mount. The electronic flip flop is designed with pins 20. This device's clock edge trigger type is Positive Edge. This part is included in FF/Latches. Compared to other similar T flip flops, this device offers reliable performance and is well suited for TR. The power supply is 5V. A total of 2ports are embedded in the D flip flop. If high efficiency is desired, the supply voltage should be kept at 5V. Additionally, it is characterized by BROADSIDE VERSION OF 374. A -6mAis set for the high level output current. It is set to 6mAfor low level output current. If the operating temperature is lower than 85°C, it is recommended. A temperature above -40°Cshould be used for the operation. Initially, it requires a voltage of 4.5V as the minimum supply voltage. In this case, it supports a maximum supply voltage of 5.5V. A frequency of 40MHzcan be achieved. It uses the logic IC BUS DRIVER. There are 1 functions available on the JK flip flop. It is equipped with 20 pins.
SN74HCT574DWRG4 Features
20 pins
5V power supplies
1 Functions
20 pin count
SN74HCT574DWRG4 Applications
There are a lot of Texas Instruments SN74HCT574DWRG4 Flip Flops applications.
- Matched Rise and Fall
- Frequency Divider circuits
- Consumer
- Individual Asynchronous Resets
- Power down protection
- Count Modes
- Safety Clamp
- Differential Individual
- Patented noise
- Test & Measurement
