SN74HCT74DBR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 14 |
| Weight | 121.789551mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HCT74 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 46MHz |
| Propagation Delay | 28 ns |
| Turn On Delay Time | 18 ns |
| Family | HCT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 4mA 4mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 25ns @ 5.5V, 50pF |
| Prop. Delay@Nom-Sup | 35 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2mm |
| Length | 6.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74HCT74DBR Overview
14-SSOP (0.209, 5.30mm Width)is the way it is packaged. Package Tape & Reel (TR)embeds it. T flip flop is configured with an output of Differential. JK flip flop uses Positive Edgeas the trigger. Surface Mountis in the way of this electric part. A voltage of 4.5V~5.5Vis used as the supply voltage. -40°C~85°C TAis the operating temperature. There is D-Type type of electronic flip flop associated with this device. In FPGA terms, D flip flop is a type of 74HCTseries FPGA. There should be no greater frequency than 46MHzon its output. This process consumes 4μA quiescents. There are 14 terminations,D latch belongs to the 74HCT74 family. A voltage of 5V is used as the power supply for this D latch. This T flip flop has a capacitance of 3pF farads at the input. Devices in the HCTfamily are electronic devices. In this case, the electronic component is mounted in the way of Surface Mount. This board has 14 pins. In this device, the clock edge trigger type is Positive Edge. It is part of the FF/Latchesbase part number family. Using 2 circuits, it is highly flexible. In view of its reliability, this D flip flop is a good fit for TR. The system runs on a power supply of 5V watts. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. Currently, there are 4 lines of input.
SN74HCT74DBR Features
Tape & Reel (TR) package
74HCT series
14 pins
5V power supplies
SN74HCT74DBR Applications
There are a lot of Texas Instruments SN74HCT74DBR Flip Flops applications.
- Automotive
- Latch
- ESD protection
- 2 – Bit synchronous counter
- Single Down Count-Control Line
- Computers
- Storage Registers
- Guaranteed simultaneous switching noise level
- Patented noise
- Differential Individual
