SN74LS273DWG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Subcategory | FF/Latches |
| Technology | TTL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 40MHz |
| Pin Count | 20 |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Current - Output | 8mA |
| Propagation Delay | 27 ns |
| Turn On Delay Time | 17 ns |
| Family | LS |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Number of Bits per Element | 8 |
| High Level Output Current | -400μA |
| Low Level Output Current | 8mA |
| Power Supply Current-Max (ICC) | 27mA |
| fmax-Min | 30 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.35mm |
| Length | 12.8mm |
| Width | 7.52mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
SN74LS273DWG4 Overview
The package is in the form of SOIC. It is configured with TTLas an output. A total of 1elements are present in it. The number of terminations is 20. A voltage of 5V is used as the power supply for this D latch. LSis the family of this D flip flop. This electronic part is mounted in the way of Surface Mount. This board has 20 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The part is included in FF/Latches. The power supply is 5V. High efficiency requires the supply voltage to be maintained at 5V. The high level output current is set to -400μA. It is set to 8mAfor the low level output current. There should be a temperature below 70°Cduring operation. A temperature above 0°Cshould be used for the operation. Despite its minimal supply voltage of 4.75V, it is capable of operating. There is a maximum supply voltage of 5.25V. The frequency that can be achieved is 40MHz. The logic IC it adopts is D FLIP-FLOP. As a result, it is equipped with 1 functions . 20pins are available on this JK flip flop. In addition to its maximum design flexibility, the output current of the flip flop is 8mA.
SN74LS273DWG4 Features
20 pins
5V power supplies
1 Functions
20 pin count
SN74LS273DWG4 Applications
There are a lot of Texas Instruments SN74LS273DWG4 Flip Flops applications.
- Frequency division
- Latch
- Parallel data storage
- Shift registers
- Balanced 24 mA output drivers
- ATE
- Consumer
- Storage Registers
- Frequency Divider circuits
- Communications
