SN74LS377DWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74LS |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | WITH HOLD MODE |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | TTL |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74LS377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Output Current | 8mA |
| Number of Bits | 8 |
| Clock Frequency | 40MHz |
| Propagation Delay | 27 ns |
| Quiescent Current | 28mA |
| Turn On Delay Time | 17 ns |
| Family | LS |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 400μA 8mA |
| Max Propagation Delay @ V, Max CL | 27ns @ 5V, 15pF |
| Trigger Type | Positive Edge |
| Number of Input Lines | 3 |
| Number of Output Lines | 2 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74LS377DWR Overview
The flip flop is packaged in 20-SOIC (0.295, 7.50mm Width). The Tape & Reel (TR)package contains it. Non-Invertedis the output configured for it. The trigger configured with it uses Positive Edge. This electronic part is mounted in the way of Surface Mount. A voltage of 4.75V~5.25Vis required for its operation. A temperature of 0°C~70°C TAis used in the operation. This logic flip flop is classified as type D-Type. It is a type of FPGA belonging to the 74LS series. There should be no greater frequency than 40MHzon its output. A total of 1 elements are present. The number of terminations is 20. You can search similar parts based on 74LS377. The power supply voltage is 5V. An electronic device belonging to the family LScan be found here. There is an electronic part mounted in the way of Surface Mount. This board has 20 pins. There is a clock edge trigger type of Positive Edgeon this device. This RS flip flops is a part number FF/Latches. It is designed with 8bits. 8 circuits are used to achieve its superior flexibility. In view of its reliability, this D flip flop is a good fit for TR. An electrical current of 5V volts is applied to it. If high efficiency is desired, the supply voltage should be kept at 5V. With a current output of 8mA , it offers maximum design flexibility. In order to operate, the chip has 2 output lines. There are 3 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. It consumes 28mA of quiescent current without being affected by external factors. As an additional reference, you may refer to electronic flip flop WITH HOLD MODE.
SN74LS377DWR Features
Tape & Reel (TR) package
74LS series
20 pins
8 Bits
5V power supplies
SN74LS377DWR Applications
There are a lot of Texas Instruments SN74LS377DWR Flip Flops applications.
- Computers
- Modulo – n – counter
- Buffered Clock
- ESD protection
- Storage Registers
- High Performance Logic for test systems
- Load Control
- Automotive
- Balanced Propagation Delays
- Reduced system switching noise
